Cubietech Cubieboard4
| Cubietech Cubieboard4 | |
|---|---|
| 250px | |
| Manufacturer | Cubietech |
| Dimensions | 111mm x 111mm |
| Release Date | December 2014 |
| Website | Cubieboard4 Product Page |
| Specifications | |
| SoC | A80 @ 1008Mhz |
| DRAM | 2GiB DDR3 @ 672MHz (SK hynix H5TQ4G63AFR-PBC 4Gb * 4) |
| NAND | 8GB eMMC (Samsung KLMAG2WEMB-B031) |
| Power | DC 5V @ 4A, optional Li-Ion battery |
| Features | |
| Video | HDMI (Type A - full), VGA |
| Audio | 3.5mm headphone plug, 3.5mm microphone plug |
| Network | WiFi 802.11 b/g/n (Ampak AP6330), 10/100/1000Mbps Ethernet (Realtek RTL8211E) |
| Storage | eMMC, µSD |
| USB | 4 USB2.0 Host, 1 USB3.0 OTG |
| Other | IRDA, Bluetooth (Ampak AP6330) |
The Cubieboard4 Board is a development board for the Allwinner A80 SoC.
Contents |
Identification
The board has a Cubietech logo, the names "Cubietech", and "CC-A80", just above the WiFi antenna.
Sunxi support
Current status
Sunxi Kernel
Like all A80 based devices, there is no support in our sunxi kernel.
Sunxi U-Boot
Like all A80 based devices, there is no support in u-boot-sunxi.
Mainline kernel
Mainline kernel support is queued up for 4.2. Currently only MMC and UARTs are supported.
Use the sun9i-a80-cubieboard4.dtb device-tree file for the mainline kernel.
Mainline u-boot
Like all A80 based devices, there is no support in mainline u-boot.
Images
HW-Pack
BSP
Manual build
Follow SDK build howto to build u-boot and the kernel from the SDK.
Mainline kernel
Initial support for the A80 based on the Cubieboard 4 board is being worked on.
Use the sun9i-a80-cubieboard4.dtb device-tree file for the mainline kernel.
Tips, Tricks, Caveats
FEL mode
There is no FEL mode button on this board.
Instead you can enter fel mode from U-Boot. While U-Boot is starting, type CTRL+C to interrupt it. At the prompt type efex to enter fel mode.
If booting fails entirely then FEL mode can be entered by shorting pin 29-30 on the nand/emmc with a suitable metal object (tweezer or the like), by vendor official procedure.
Expansion Ports
The Cubieboard4 board exposes a 2 mm pitch connector for GPIO.
GPIO Connector
The pinout is printed on the board:
SECTION NOT UPDATED YET
| 2x16 GPIO Header | |||
|---|---|---|---|
| 1 | GPIO-ADC0 | 2 | GPIO-PL0-CPUS-TX |
| 3 | GPIO-ADC1 | 4 | GPIO-PL1-CPUS-RX |
| 5 | GND | 6 | GPIO-3V |
| 7 | GPIO-HSIC-STRB | 8 | GND |
| 9 | GND | 10 | GPIO-PH6-PWM0 |
| 11 | GPIO-HSIC-DATA | 12 | GND |
| 13 | GND | 14 | GPIO-PH14-SPI3-CLK |
| 15 | GPIO-PL7-1WIRE | 16 | GPIO-PH15-SPI3-MOSI |
| 17 | GPIO-PM0 | 18 | GPIO-PH16-SPI3-MISO |
| 19 | GPIO-PM1 | 20 | GPIO-PH17-SPI3-CS0 |
| 21 | GPIO-PM2 | 22 | GPIO-PG10-TWI3-SCK |
| 23 | GPIO-PM3 | 24 | GPIO-PG11-TWI3-SDA |
| 25 | GPIO-PM4 | 26 | GPIO-PG12-UART4-TX |
| 27 | GPIO-PM8 | 28 | GPIO-PG13-UART4-RX |
| 29 | GPIO-PM9 | 30 | GPIO-PG14-UART4-RTS |
| 31 | GPIO-PH2 | 32 | GPIO-PG15-UART4-CTS |
Serial console port
The UART header is next to the VGA port. Pinout is printed in small font next to the header.
| 1x4 UART Header | |
|---|---|
| 1 | GPIO-PH12-UART0-TX |
| 2 | GPIO-PH13-UART0-RX |
| 3 | NC |
| 4 | GND |
Pictures
Will be uploaded later
- Cubieboard4 front.jpg
- Cubieboard4 back.jpg
- Cubieboard4 board front.JPG
- Cubieboard4 Board features.jpg
Also known as
Cubietech also uses the name "CC-A80", both printed on the board and on their websites, for this board.
See also
Manufacturer images
Cubietech provides firmware images on their "Cubieboard Docs" website.
